Loyola Enterprises

A veteran and minority owned SDB Certified Business.

Electro-Voice















Electro-Voice P 2000


757.498.6118 Ext - 109P 2000 - Call for pricing - Power Amplifier

Downloads

PDFP 2000 Specifications (pdf)

PDFP 2000 Manual (pdf)


Specifications

Standard specifications: IEC 268 part 3 , IHF-A
0 dBu = 775 mV (RMS)

A. POWER SUPPLY

1. Mains:AC
2. Rated mains voltage:120 V
3. Rated mains frequency:60 Hz
4. Rated power consumption:2950 watts
5. Normal power consumption:1000 watts
6. Power consumption at 1/8 rated output:1100 watts
7. Tolerance of mains voltage:±10%

B. INPUT CHARACTERISTICS

• All level controls fully opened

Input socketsRated Input Level (rated source e.m.f.)Rated Output PowerRated Load Impedance
0dBu Jumper internal+6dBu Jumper internal26 dB Jumper internal
CHANNEL A/B+1dBu (870mV)+7dBu (1.74V)12.2dBu (3.16V)500W8 ohms
CHANNEL A/B0dBu (775mV)+6dBu (1.55V)11.2dBu (2.82V)800W4 ohms
CHANNEL (Bridged)0dBu (775mV)+6dBu (1.55V)11.2dBu (2.82V)1600W8 ohms

Maximum Input Level: +21dBu (9V)

C. OUTPUT CHARACTERISTICS

• Rated output power at THD = <0.1%. 20 Hz–20 kHz, MBW = 80 kHz
• Maximum Output Power at 1 kHz / THD = 1%

Output socketsRated Load ImpedanceRated Output Power Dual ModeMaximum Ouput Power, Dual Mode THD = 1%Single Channel Output Power *1Rated Output Voltage
SPEAKER (A/B)8 ohms500W560W650W63.2V
SPEAKER (A/B)4 ohms800W900W1150W56.6V
SPEAKER BRIDGED8 ohms1600W1800W2300W113.2V

*1: measured with "Dynamic Headroom" test signal according IHF-A: 1 kHz tone burst, 20ms ON, 480ms OFF

D. MAXIMUM OUTPUT VOLTAGE (NO-LOAD)

Output socketSPEAKER A/BSPEAKER BRIDGED
Max. output voltage (no-load)72V (RMS)146V (RMS)

E. STABILIZATION

with rated load impedance, Dual Mode, standard test conditions

8 ohms4 ohms
Stabilization0.35%0.56%
Stabilization level0.03 dB0.048 dB

F. FREQUENCY RESPONSE

Gain frequency response:
-3 dB loss against level at norm frequency
1. INPUT → SPEAKER: <10 Hz to 75 kHz - HI-LO-CUT off
2. INPUT → SPEAKER: 20 Hz to 35 kHz - HI-LO-CUT on

Distortion-limited effective frequency range (power bandwidth):
THD = 0.1%, 1/2 rated power into 4 ohms, MBW = 500 kHz
1. INPUT → SPEAKER: <10 Hz to 50 kHz - HI=LO=CUT off

G. PHASE RESPONSE

±45° (10 Hz–30 kHz, HI-LO-CUT off)

H. INPUT IMPEDANCE

20 kohms (20 Hz–20 kHz)

I. AMPLITUDE NON-LINEARITIES

1. Rated Total Harmonic Distortion (1 kHz)k ≤ 0.05%
2. IMD - SMPTE - 60 Hz, 7 kHzk ≤0.01%
3. DIM 30k ≤ 0.01%
4. DIM 100k ≤ 0.01%

J. CROSSTALK

at f = 1 kHz and rated power<-70 dB

K. DAMPING FACTOR

internal at f = 1 kHz>300

L. SLEW RATE

internal>35 V/μs

M. NOISE

  • R(S) = 50 ohms
  • Power amplifier input sensitivity 0dBu
  • E(F) = Noise voltage, unweighted with B = 22 Hz – 22 kHz, RMS (IEC 268-1)
  • E(G) = Noise voltage, frequency weighting filter according CCIR-4683, quasi peak-weighted (IEC 268-1)
  • E(A) = Noise voltage, dB(A) frequency-weighted, RMS (IEC 268-1)
  • S/N ratios ref. rated output voltage 56.6V (800W/4ohms)
  • HI/LO-CUT ON, GND LIFT = GROUNDED
  • i.s. = Input Sensitivity
Noise-
Voltage
S/N-
Ratio
equiv. input
noise voltage
equiv. input
noise level
residual noise
output voltage
E(F)<550 μV>100 dB<7.5 μV<-100 dBu<350 μV
E(G)<1.48 mV>89.7 dB<25 μV<-89.7 dBu<1.23 mV
E(A) i.s.=0dBu<440 μV>102 dB<6.0 μV<-102 dBu<320 μV
E(A) i.s.=6dBu<220 μV>108 dB<6.0 μV<-102 dBu<160 μV
E(A) i.s.=26dB<120 μV>113.5 dB<6.0 μV<-102 dBu<90 μV

N. DIMENSIONS

Height: 132.5mm (5.25")
Width: 483mm (19")
Depth: 426mm (16.77")

O. WEIGHT

26 kg (57.3 lbs)

Purchasing
For pricing options and packages, contact us at
757.498.6118 Ext - 109, Or