Loyola Enterprises

A veteran and minority owned SDB Certified Business.

Electro-Voice















Electro-Voice CP 1200


757.498.6118 Ext - 109CP 1200 - Call for pricing - Power Amplifier

Downloads

PDFCP Series Brochure (pdf)

PDFCP Series Manual (pdf)


The CP Series are high-performance amplifiers with unmatched dynamic range capability, ensuring the most reliable operation favored by sound contractors in all sound reinforcement applications.

The audio performance of the CP 1200 power amp is simply extraordinary. Optimized power supply units employing low-leakage toroidal transformers provide extensive headroom far above the stated nominal output. This allows a reduction in the overall weight and power dissipation of the amplifier without sacrificing performance or reliability.

With up to 2 x 600 watts into 2 ohms and 2 x 400 watts into 4 ohms, the CP 1200 is dedicated for small full-range cabinets and individual hi-frequency components in multiway systems. The CP 1200 uses a conventional transformer power supply.

Designed in Class-AB technology, the CP 1200 has been designed to fulfill even the most demanding requirements of touring applications. The CP 1200 amp is protected against thermal and electrical overload, short circuit and the occurrence of HF/DC at the outputs. Back-EMF-Protection eliminates the risk of the output transistors being damaged by electrical energy back-feed. The power outputs are switched via relay with a time delay during soft-start. An inrush current limiter prevents mains fuses from blowing.

The recessed mounted dB-scaled level controls ensure reliable protection against mechanical damage. These particularly precise, secure to operate detent-potentiometers are located on the front panel. CP-Series power amps provide the opportunity for retrofitting an internal analogue signal processor board with x-over and filter functions.

The easily readable LED display provides a quick overview of the power amp’s current operational status. The power outputs CHANNEL A, CHANNEL B and BRIDGED OUT are carried out as extremely durable Speakon-type connectors. Also located on the rear panel is a Ground-lift switch, which helps eliminating ground-noise loops by separating the power amp’s enclosure from the circuit ground. In normal operation, the CP 1200 power amp is capable of driving loads as low as 2 ohms. In Mono-Bridged mode the allowable minimum load is 4 ohms.

Features

  • 2 x 600W/2 Ohms
  • 2 U Rack Space
  • Only 30 lbs (13.5 kg)
  • Complete Protection Package
  • Dynamic Limiter

Specifications
2 Ω4 Ω8 Ω
Max. Midband Output Power - THD=1%, 1 kHz, Dual Channel 600 W 400 W 240 W
Rated Output Power - THD=0.1%, 20 Hz–20 kHz - 300 W 150 W
Max. Single Channel Output Power - Dynamic Headroom, IHF-A 1100 W 580 W 300 W
Max. Single Channel Output Power - Continuous, 1 kHz 800 W 480 W 270 W
Max. Bridged Output Power - THD=1%, 1 kHz - 1200 W 800 W
Maximum RMS Voltage Swing - THD=1%, 1 kHz 50 V
Power Bandwidth - THD=1%, 1 kHz, half power @ 4Ω 10 Hz–60 kHz
Voltage Gain - ref. 1 kHz 32.0 dB
Input Sensitivity - Rated power @ 8Ω, 1 kHz +1.15 dBu (0.88 Vrms)
THD @ rated output power - MBW=80 kHz, 1 kHz < 0.05%
IMD-SMPTE - 60 Hz, 7 kHz < 0.02%
DIM-30 - 3.15 kHz, 15 kHz < 0.01%
Maximum Input Level - ref. 1 kHz +22 dBu (9.76 Vrms)
Crosstalk - ref. 1 kHz, rated output power < -80 dB
Frequency Response (±1 dB, ref. 1 kHz) 15 Hz–40 kHz
Input Impedance - active balanced 20 kΩ
Damping Factor - 1 kHz > 300
Slew Rate 25 V/μs
Signal to Noise Ratio (A-weighted) 103.5 dB
Output Noise (A-weighted) < -70 dBu
Output Stage Topology Class AB
Power Requirement 240V, 230V, 220V, 120V or 100V; 50–60 Hz
Power Consumption 600 W
Protection Audio limiters, High temperature, DC, HF, Back-EMF, Peak current limiters, Inrush current limiters, Turn-on delay
Cooling Front-to-rear, 3-stage fans
Ambient Temp. Limits 5° C–40° C (40° F–105° F)
Safety Class I
Dimensions (HxWxD) 8.81 x 48.3 x 38.7 cm (3.5" x 19.0" x 15.2")
Weight 13.5 kg (29.76 lbs)
Purchasing
For pricing options and packages, contact us at
757.498.6118 Ext - 109, Or